Skip to main content

Accessories

Helmet/Mask Bag
Measurements: 16’’ length x 12’’ width x 16’’ height. Made of high quality, tough black nylon, encasing a lightweight, white polyethylene foam that features low water absorption and is fairly rigid (good impact strength). The two grommeted ventilation holes seen in the photo are on both sides of the bag. A large elastic topped pocket is on each side, for holding tool kits, checklists, logbooks, spares, etc. (There are no inside pockets). The bag handles are 1” wide straps of black polyester webbing. The bag closes up with two, large YKK zippers. We do not recommend the 500-901 helmet bag as a shipping container or packaging for your Kirby Morgan life support equipment!
Part # 500-901
125-001 Maintenance and Repair Log Book with Pen
Logbook w/ pen
  
Part # 125-001
Manual KM 37SS
This is your operations and maintenance manual. It is a writable USB flash drive which enables you to add or subtract the manual PDF sections as they are updated or when you purchase new Kirby Morgan products.
Part # 100-063
200-017 Overpressure Relief Valve
Overpressure Relief Valve
The Kirby Morgan® Overpressure Relief Valve is factory adjusted to vent any time the pressure in the low pressure hose connecting the bailout bottle to your emergency valve exceeds 200 P.S.I. It is installed in any of the low pressure ports in the first stage regulator.
Part # 200-017
Restrictor Adapter
The 555-210 Restrictor Adapter should be used when an inflation hose is attached to the side block when drysuit diving. The main purpose of the Restrictor Adapter is to limit gas flow in the event the hose ruptures or is severed, and to ensure the loss of supply would not be great enough to significantly affect the diver’s breathing at moderate to heavy work rates. It also helps prevent filling the dry suit too rapidly.   NOTE: O-ring 310-003 is required to install the Restrictor Adaptor onto the side block.  
Part # 555-210
SuperFlow First Stage, No Hose
 
Part # 305-161

Accessories-Kits

Chin Cushion
Chin Cushion
Part # : 510-683
525-430 Communications Module for MWP Kit
Communications Module for MWP Kit
Part # : 525-430
525-420 Communications Module for Posts Kit contents
Communications Module for Posts Kit
Part # : 525-420
455 Regulator
Conversion Kit, 455 Regulator for 350/450 Regulators
Part # : 525-765
525-395 Conversion Kit, REX Regulator for 37SS
Conversion Kit, REX Regulator for 37SS
Part # : 525-395
525-230
Dry Suit Neck Ring Kit For All Kirby Morgan® Helmets (Except the SL 17B)
Part # : 525-230
525-116
Front Standoff Kit
Part # : 525-116
Head Cushion Assembly
Head Cushion Assembly
Part # : 510-754
525-390 KM 37SS Water Shroud Kit
KM 37SS Water Shroud Kit
Part # : 525-390
Lens Retainer Kit
Lens Retainer Kit
Part # : 525-776
Oral Nasal With Lens Retainer Kit
Oral Nasal With Lens Retainer Kit
Part # : 525-775
525-112 Pull Pin Sleeve
Pull Pin Sleeve
Part # : 525-112
525-746
Replacement Foam Kit for 510-754 Head Cushion
Part # : 525-746
525-715 Stainless Helmet Handle Grip Kit
Stainless Helmet Handle Grip Kit
Part # : 525-715
525-771
SuperFlow® 350 Regulator Assembly Kit
Part # : 525-771
Welding Lens Assembly
Weld Lens Kit
Part # : 525-403
Welding Shield Assembly
Welding Shield Assembly
Part # : 525-400